Customer Gallery
Here are just a few of many awesome vehicles out on the highways, city streets, dragstrips and motorsports venues that are using Moser Engineering parts to gain an advantage over the competition. If you are proud of your vehicle and currently use Moser Engineering products then let the world know it. Be sure to tell us all about the products you are using and any wins, events, stories or accomplishments that you would like to share. Get your dragster, car, streetrod or truck featured here for maximum exposure and who knows, you might even get a call from us wanting to use your car in a national advertising campaign!
- Horsepower:
- Torque:
- Make: Ford
- Year: 1964
1964 Ford F-100, 468 with a 671 weiand blower. Built 350 trans, 9″ ford rear end, with all new Moser components.Built for the street. Several years in the making. Eye catcher and a blast to drive. Thanks again to Moser for the excellant service while I waited for my parts after a 5 hour one way drive to get them. THANKS AGAIN MIKE.
View Gallery
- Horsepower: 3000 plus
- Torque:
- Make: 4X4 all wheel drive p/u
- Year: 1987
The worlds only all wheel drive outlaw 10.5 4X4 vehicle . powered by a PSI screw blown 541 cid KB Olds with a bruno/liberty , SCS transfer , and equipped with Moser 40 spline rear axles , moser max front axles , moser housing ends , aluminum moser center sections in both ends , moser titanium 5/8 drive studs in the rear
View Gallery
- Horsepower: 435 +
- Torque: 429 +
- Make: Chevy
- Year: 1995
1st I saw your M9 rear end at the sema show 3 years a go. I needed it. lol Okay I have a 1995 Impala SS. I put a 383 Lt-1 eng. in very happy with it, but could not get it to hook up. So we did a body off with a full tub. 2 batterys and fuel cel in the trunk. I went with the M9 rear end and with Moser axels and disk brakes. That is the best looking rear end in Arizona. Right now I’m running a 15X15 Rear rim with 29X18.5X15 tire. I need to find a used 31×18x15 to see if it will fit. I put a 4 link on. It runs just need to order a drive shaft and get a cage. U can go to www.cardomain.com Then put in LT1383IMPALASS to see all of the photos. P.S. Moser is on FACE BOOK
View Gallery
- Horsepower: Black top DYNO
- Torque: Unknown
- Make: FORD
- Year: 1995
1995 Mustang SBC with P/G Moser 33 Spline axles, spool, gears and Nodular third member. Second place winner at CARL CASPERS AUTO SHOW. Best appearing car at Indy Bracket finals. best appearing car at Beechbend Raceway, and 2006 King of the Track WALLY WINNER at BG.
View Gallery
- Horsepower:
- Torque:
- Make: chevrolet
- Year: 2000
ls1
nos
stock suspension
street car
drag radials
moser 9inch
35 spline axles
moser center section
View Gallery
- Horsepower:
- Torque:
- Make: Chevrolet
- Year: 1966
View Gallery
To submit your vehicle, please follow these simple step-by-step instructions:
- Upload picture at 640 x 480 pixels & 72 dpi.
- Photos can be in JPG, GIF, or PNG Format.
- Fill out the form below.
- Enter a Description for your Vehicle.
- Click "Submit".
Moser Engineering reserves the right to either upload your car to the website or decline it. Check back within a few days to see if your car is "live".