***CANCELLED ORDER*** Complete M9 Fabricated 2008-09 Pontiac G8 or 2010-15 Camaro Rear Solid Axle!

  • M9 Fabricated Gen 5 Camaro Rear Solid Axle Sub Frame Kit!
  • COPO_Camaro.jpg
  • 2008-pontiac-g8-photo-173024-s-986x603.jpg

M9GEN5-COMPLETE

***NEW UNIT CANCELED ORDER!***

The New Moser Engineering "Gen V" Rear Sub Frame Kit!
Convert your street car into a COPO clone for a lot less money!
Fits:
2008 - 2009 Pontiac G8
2010 - 15 Chevrolet Camaro
*Kit ships same day if ordered before 1:00pm
The standard kit includes the following;
M9 Fabricated Mild-Steel 9" Housing 61 1/2" Wide (67" Wheel to Wheel)
Moser 35 Spline Alloy Axles
1/2"-20 X 2" Screw-In Studs
Sealed Axle Bearings
Chrome Moly - Torque Arm, Driveshaft Loop, Transmission Cross-member, Panhard Bar, Track Locator, Lower Control Arms, Spring Saddles, Anti-Roll Adjuster, Anti-Roll Arm, Anti-Roll Tubes and Frame Rails
Mild Steel - Front Cross-member, Rear Cross-member, Upper Shock Mounts, Spring Mounts
All Associated Hardware is supplied!
Aluminum 3.250" Thru-Bolt Case
35 Spline Eaton Truetrac Limited Slip Posi
1350 Series Chroem Moly Pinion Yoke
3.25:1 Ratio US Gear
Wilwood Low-Profile Disc Brake Kit w/Drilled Rotors (140-11389-D)
Stainless Steel Flex Line Hose Kit
Lokar Emergency Brake Cables
JRi - Double Adjustable Coil-Over Shocks
200 lbs. Chrome Springs
Housing and Sub-Frame Assembly are Powder Coated Semi-Gloss Black!
Center section is set-up, but will need installed in housing, brakes are shipped in a boxed kit, this unit is not a MusclePak, ASSEMBLY REQUIRED!!!

PRODUCT DESCRIPTION
The Moser Engineering rear sub frame kit for the 2008 - 2009 Pontiac G8 & 2010 - 2014 Camaro!
The installation of this kit requires Fabrication/Welding skills and should not be attempted by a novice!
***You cannot use the OEM fuel tank, an aftermarket Fuel Cell is required!

Sale

$8,992.50

$7,750.00

***CANCELED ORDER***

The Moser Engineering "Gen V" Rear Sub Frame Kit!
Convert your street car into a COPO clone for a lot less money!
Fits:
     2008 - 2009 Pontiac G8
     2010 2011 2012 2013 2014 & 2015 Chevrolet Camaro

*Kit ships same day if ordered before 1:00pm
The standard kit includes the following;
  • M9 Fabricated 9" Mild-Steel Housing 61 1/2" Wide (67" Wheel to Wheel)
  • Moser 35 Spline Alloy Axles
  • 1/2"-20 X 2" Screw-In Studs
  • Sealed Axle Bearings
  • Chrome Moly - Torque Arm, Driveshaft Loop, Transmission Cross-member, Panhard Bar, Track Locator, Lower Control Arms, Spring Saddles, Anti-Roll Adjuster, Anti-Roll Arm, Anti-Roll Tubes and Frame Rails
  • Mild Steel - Front Cross-member, Rear Cross-member, Upper Shock Mounts, Spring Mounts
  • All Associated Hardware is supplied!
  • Aluminum 3.250" Thru-Bolt Case
  • 35 Spline Eaton Truetrac Limited Slip Posi
  • 1350 Series Chroem Moly Pinion Yoke
  • 3.25:1 Ratio US Gear
  • Wilwood Low-Profile Disc Brake Kit w/Drilled Rotors (140-11389-D)
  • Stainless Steel Flex Line Hose Kit
  • Lokar Emergency Brake Cables
  • JRi - Double Adjustable Coil-Over Shocks
  • 200 lbs. Chrome Springs
  • Housing and Sub-Frame Assembly are Powder Coated Semi-Gloss Black!
 
PRODUCT DESCRIPTION
The Moser Engineering rear sub frame kit for the 2010 - 2015 Camaro & 2008 - 2009 Pontiac G8!
The installation of this kit requires Fabrication/Welding skills and should not be attempted by a novice!
***You cannot use the OEM fuel tank, an aftermarket Fuel Cell is required!